Share:
Detector Module ModuLaser Detector Module
Detector Module
The Detector Module is a fully self-contained unit, which aspirate the sampled air from the protected area, analyze the air and based on ClassiFire determine if a pre-alarm or alarm should be raise, if smoke particles would be present in the sampled air. If an alarm condition or fault condition would occur, then the unit will activate the corresponding local relay output, subjected to the programming of the relays. Simultaneously the alarm or fault condition would also be reported to the Display Module to which the Detector Module is connected.
Due to the modular nature of the ModuLaser, maintenance (for example routine filter replacement) can be done on a module per module bases, rather than a complete system. This in turn reduces the risk of the area which is unprotected during the maintenance period, as only one sampling pipe (protected zone) would be affected at a time.
- Modular Design: Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap
- Zoned aspirating smoke detection: Individual detector modules provide detection for individual areas or zones, specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module
- Simplified installation: Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit
- Intuitive user interface: Bright easy-to-see color TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics
- Easy pipe connection: The quick fit pipe adaptor system locks down securely, yet leaves plenty of room for easy pipe connection and removal
- Quick location of smoke: Each detector module is self-contained, which means no delays in determining in which zone (sampling pipe) smoke is present
General
- Status indication: LED's
- User interface: TFT and navigation buttons on Normal and Command Display Modules
- Alarm levels: 4 (Aux, Pre-alarm, Alarm and Alarm 2)
- Event log: 20 000 events per module
- RS485 support: Yes (SenseNET and SenseNET+)
- Connectivity: USB (x2), IP and APIC on Display Module
Electrical
- Operating voltage: 18 to 30 VDC
- Current consumption:
Display Module (at 24 VDC):
204 mA - Minimum Display Module
232 mA - Standard Display Module
232 mA - Command Display Module
Detector Module (at 24 VDC):
260 mA - fan speed 1
380 mA - fan speed 6 (default speed)
940 mA - fan speed 16
Detection
- Detection principle: Laser light scattering mass detection and particle evaluation
- Particle sensitivity range: 0.003 to 10 microns
Sampling pipe
- Length: Up to 250 m (820 ft.) combined per detector module
- Quantity sampling holes:
Up to 20 - Class A per detector module
Up to 40 - Class B per detector module
Up to 50 - Class C per detector module - Inlet size: 27 or 25 mm (1.06 or 0.98 in) outer diameter
- Inlet location: Top or bottom
- Exhaust size: 27 or 25 mm (1.06 or 0.98 in) outer diameter
- Exhaust location: Top or bottom
Input
- Input quantity: 2 per module
- Input type and rating: Supervised
- Termination: 15 KΩ 5% 1/4 W
- Programmable: Yes
Output
- Output quantity: 3 per module
- Output type and rating: Voltage free (contact rating 2 A at 30 VDC / NO/NC/C)
- Programmable: Yes
Physical
- Physical dimensions: W x D x H 110.5 x 133.5 x 300 mm (4.35 x 5.25 x 11.8 in)
- Net weight: Display Module: 1.18 Kg (2.6 lb.) Detector Module: 1.57 Kg (3.46 lb.)
- Colour: Cream
- Mounting type: Surface mount
- Cable entries: 2 at the bottom, 2 at the rear, 2 at the top on Detector Module, and 3 at the top on the Display Module
Environmental
- Operating temperature:
Equipment: -20 to +60 °C (-4 to +140 °F)
Sampled air: -20 to +60 °C (-4 to +140 °F) - Relative humidity: 0 to 95% noncondensing
- Environment: Indoor
- IP rating: IP40
Standards & Regulation
- Compliancy: REACH, RoHS
- Certification: BOSEC, CPR, CSIRO, EN54-20, LPCB
- REACH
- RoHS
- BOSEC
- CPR
- CSIRO
- EN54-20
- LPCB
- Modular Design: Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap
- Zoned aspirating smoke detection: Individual detector modules provide detection for individual areas or zones, specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module
- Simplified installation: Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit
- Intuitive user interface: Bright easy-to-see color TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics
- Easy pipe connection: The quick fit pipe adaptor system locks down securely, yet leaves plenty of room for easy pipe connection and removal
- Quick location of smoke: Each detector module is self-contained, which means no delays in determining in which zone (sampling pipe) smoke is present
General
- Status indication: LED's
- User interface: TFT and navigation buttons on Normal and Command Display Modules
- Alarm levels: 4 (Aux, Pre-alarm, Alarm and Alarm 2)
- Event log: 20 000 events per module
- RS485 support: Yes (SenseNET and SenseNET+)
- Connectivity: USB (x2), IP and APIC on Display Module
Electrical
- Operating voltage: 18 to 30 VDC
- Current consumption:
Display Module (at 24 VDC):
204 mA - Minimum Display Module
232 mA - Standard Display Module
232 mA - Command Display Module
Detector Module (at 24 VDC):
260 mA - fan speed 1
380 mA - fan speed 6 (default speed)
940 mA - fan speed 16
Detection
- Detection principle: Laser light scattering mass detection and particle evaluation
- Particle sensitivity range: 0.003 to 10 microns
Sampling pipe
- Length: Up to 250 m (820 ft.) combined per detector module
- Quantity sampling holes:
Up to 20 - Class A per detector module
Up to 40 - Class B per detector module
Up to 50 - Class C per detector module - Inlet size: 27 or 25 mm (1.06 or 0.98 in) outer diameter
- Inlet location: Top or bottom
- Exhaust size: 27 or 25 mm (1.06 or 0.98 in) outer diameter
- Exhaust location: Top or bottom
Input
- Input quantity: 2 per module
- Input type and rating: Supervised
- Termination: 15 KΩ 5% 1/4 W
- Programmable: Yes
Output
- Output quantity: 3 per module
- Output type and rating: Voltage free (contact rating 2 A at 30 VDC / NO/NC/C)
- Programmable: Yes
Physical
- Physical dimensions: W x D x H 110.5 x 133.5 x 300 mm (4.35 x 5.25 x 11.8 in)
- Net weight: Display Module: 1.18 Kg (2.6 lb.) Detector Module: 1.57 Kg (3.46 lb.)
- Colour: Cream
- Mounting type: Surface mount
- Cable entries: 2 at the bottom, 2 at the rear, 2 at the top on Detector Module, and 3 at the top on the Display Module
Environmental
- Operating temperature:
Equipment: -20 to +60 °C (-4 to +140 °F)
Sampled air: -20 to +60 °C (-4 to +140 °F) - Relative humidity: 0 to 95% noncondensing
- Environment: Indoor
- IP rating: IP40
Standards & Regulation
- Compliancy: REACH, RoHS
- Certification: BOSEC, CPR, CSIRO, EN54-20, LPCB
- REACH
- RoHS
- BOSEC
- CPR
- CSIRO
- EN54-20
- LPCB