Share:
Li-ion Tamer GEN 2 Li-ion Tamer
Li-ion Tamer GEN 2
The Li-ion Tamer Rack Monitoring system is a safety product that monitors lithium-ion battery off-gas events. Off-gas events occur early in the failure mode of lithium-ion batteries and very early detection of these events allow proper mitigation steps to be taken to avoid a catastrophic thermal runaway failure.
Li-ion Tamer is a unique protection technology that offers the earliest warning to avoid catastrophic events.
- Early warning of lithium-ion battery failures
- Enable thermal runaway prevention with proper mitigation actions
- Single cell failure detection without electrical or mechanical contact of cells
- Extended product lifetime
- Calibration-free product
- Highly reliable output signal
- Low power consumption
- Compatible with all lithium-ion battery form factors and chemistries
- Easy installation with several mounting options
- Independent and redundant perspective on battery health
- Auto diagnostic capabilities
- Reduction/removal of false positive signals
- Several communication protocols including digital outputs and Modbus communication
Controller Specifications
- Dimensions [mm]: 210 (W) x 113 (L) x 63 (H)
- Input power range: 12 - 28 VDC
- Max sensors per controller: 15
- System outputs: Digital outputs/MODBUS
Power Consumption Specifications
- Controller (no sensors): 2.4 W (@ 24VDC); 1.4 W (@ 12 VDC)
- Sensor: 275 mW (@ 5 VDC)
- Controller (fullypopulated, 15 sensors): 6.6 W (@ 24 VDC)<5.6 W (@ 12 VDC)
- Fuse Rating: 3.5A]
MODBUS Communication Specifications
- Baud rate: 9600
- Parity: None
- Stop bit: One
- Hardware: RS232 3-wire (TX, RX, ground)
Product Life Specifications
- Target Lifetime: 10 years
- Warranty: 1 year
Gas Detection Specifications
- Target gases: Lithium ion battery off-gassing compounds
- Min. detection threshold: <1 ppm/sec
- Response Time: 5 seconds
- Fault detection: Single cell failure
Environmental Specifications
- Temperature: -10 to +60oC
- Humidity: 5 to 95% RH
- Max. temperature change: 8.6oC/min
Digital Output Specifications
- Connector type: 2x 10-pin Molex
- Signal type: Digital
- Signal level, normal: HIGH, 12 - 28 VDC (input voltage) 100mA max per channel
- Signal level, alarm: LOW
- ETL listed to UL 61010 and CSA 22.2 NO. 61010 for product safety
- EN 61326 for EU Directive (2014/30/EU)
- RoHS 3 EU 2015/863
- Early warning of lithium-ion battery failures
- Enable thermal runaway prevention with proper mitigation actions
- Single cell failure detection without electrical or mechanical contact of cells
- Extended product lifetime
- Calibration-free product
- Highly reliable output signal
- Low power consumption
- Compatible with all lithium-ion battery form factors and chemistries
- Easy installation with several mounting options
- Independent and redundant perspective on battery health
- Auto diagnostic capabilities
- Reduction/removal of false positive signals
- Several communication protocols including digital outputs and Modbus communication
Controller Specifications
- Dimensions [mm]: 210 (W) x 113 (L) x 63 (H)
- Input power range: 12 - 28 VDC
- Max sensors per controller: 15
- System outputs: Digital outputs/MODBUS
Power Consumption Specifications
- Controller (no sensors): 2.4 W (@ 24VDC); 1.4 W (@ 12 VDC)
- Sensor: 275 mW (@ 5 VDC)
- Controller (fullypopulated, 15 sensors): 6.6 W (@ 24 VDC)<5.6 W (@ 12 VDC)
- Fuse Rating: 3.5A]
MODBUS Communication Specifications
- Baud rate: 9600
- Parity: None
- Stop bit: One
- Hardware: RS232 3-wire (TX, RX, ground)
Product Life Specifications
- Target Lifetime: 10 years
- Warranty: 1 year
Gas Detection Specifications
- Target gases: Lithium ion battery off-gassing compounds
- Min. detection threshold: <1 ppm/sec
- Response Time: 5 seconds
- Fault detection: Single cell failure
Environmental Specifications
- Temperature: -10 to +60oC
- Humidity: 5 to 95% RH
- Max. temperature change: 8.6oC/min
Digital Output Specifications
- Connector type: 2x 10-pin Molex
- Signal type: Digital
- Signal level, normal: HIGH, 12 - 28 VDC (input voltage) 100mA max per channel
- Signal level, alarm: LOW
- ETL listed to UL 61010 and CSA 22.2 NO. 61010 for product safety
- EN 61326 for EU Directive (2014/30/EU)
- RoHS 3 EU 2015/863