Share:
Li-ion Tamer GEN 3 Li-ion Tamer GEN 3
Li-ion Tamer GEN 3
The Li-ion Tamer GEN 3 is a device that detects the venting of battery electrolyte solvent vapours (off-gassing phase) that occurs early in the failure mode of lithium-ion batteries (LIB). The early detection of this event allows proper mitigation steps to be taken to avoid a catastrophic thermal runaway failure.
The Li-ion Tamer GEN 3 system is designed to be easy to install and configure, consisting of several components: (i) sensors, (ii) hub, (iii) power switch, (iv) network switch, (v) controller.
- Early warning of lithium-ion battery failures - enable thermal runaway prevention with proper mitigating actions
- Single cell failure detection without mechanical or electrical contact to the cells
- Scalable deployment for cost effective protection of a wide range of battery storage systems
- Temperature and humidity monitoring at each sensing node
- Extended product lifetime
- Calibration-free product with highly reliable output signal
- Compatible with all lithium-ion battery form factors and chemistries
- Easy installation
- Independent and redundant perspective on battery health
- Auto diagnostic capabilities
- Reduction/removal of false positive signals
- Communication protocols including relays and Modbus serial
Controller Specifications
- Dimensions [mm]: 115mm x 82mm x 34mm
- Input power range: 12 VDC
- Max sensors per controller: 100*
Power Consumption Specifications
- Controller: 36 W (@ 12 VDC)
- Hub (Fully Populated): 6.0 W (@ 12 VDC)
- Additional Hardware: See User Manual for details
MODBUS Output Specifications
- Hardware: TCP/IP Ethernet
- Connector Type: Screw Terminals
- Signal Type: 16 SPDT Form C Relays; See User Manual for details
Product Life Specifications
- Target Lifetime: >10 years
Gas Detection Specifications
- Target gases: Lithium ion battery electrolyte solvent vapours
- Min. detection threshold: <1 ppm/sec
- Response Time: 5 seconds
- Fault detection: Single cell failure
Temperature Measurement Specifications
- Measurement Range: -40 to +125oC
- Measurement Accuracy: +/-0.4oC from 5 to 60oC
Humidity Measurement Specifications
- Measurement Range: 0 to 100% RH (non-condensing)
- Measurement Accuracy: +/-2.0% RH from 20 to 80% RH
Environmental Specifications
- Operating Temperature: Controllers: 0 to 40oC; Sensors and Hubs: -10 to 50oC
- Humidity: 10 to 90% RH (non-condensing)
* Expandable up to 500 sensors per controller in future release.
- ETL listed to UL 61010 and CSA 22.2 NO. 61010 for product safety
- EN 61326-1:2013 for EU Directive (2014/30/EU)
- RoHS 3 EU 2015/863, WEEE, and REACH compliant
- UKCA
- FCC
- Early warning of lithium-ion battery failures - enable thermal runaway prevention with proper mitigating actions
- Single cell failure detection without mechanical or electrical contact to the cells
- Scalable deployment for cost effective protection of a wide range of battery storage systems
- Temperature and humidity monitoring at each sensing node
- Extended product lifetime
- Calibration-free product with highly reliable output signal
- Compatible with all lithium-ion battery form factors and chemistries
- Easy installation
- Independent and redundant perspective on battery health
- Auto diagnostic capabilities
- Reduction/removal of false positive signals
- Communication protocols including relays and Modbus serial
Controller Specifications
- Dimensions [mm]: 115mm x 82mm x 34mm
- Input power range: 12 VDC
- Max sensors per controller: 100*
Power Consumption Specifications
- Controller: 36 W (@ 12 VDC)
- Hub (Fully Populated): 6.0 W (@ 12 VDC)
- Additional Hardware: See User Manual for details
MODBUS Output Specifications
- Hardware: TCP/IP Ethernet
- Connector Type: Screw Terminals
- Signal Type: 16 SPDT Form C Relays; See User Manual for details
Product Life Specifications
- Target Lifetime: >10 years
Gas Detection Specifications
- Target gases: Lithium ion battery electrolyte solvent vapours
- Min. detection threshold: <1 ppm/sec
- Response Time: 5 seconds
- Fault detection: Single cell failure
Temperature Measurement Specifications
- Measurement Range: -40 to +125oC
- Measurement Accuracy: +/-0.4oC from 5 to 60oC
Humidity Measurement Specifications
- Measurement Range: 0 to 100% RH (non-condensing)
- Measurement Accuracy: +/-2.0% RH from 20 to 80% RH
Environmental Specifications
- Operating Temperature: Controllers: 0 to 40oC; Sensors and Hubs: -10 to 50oC
- Humidity: 10 to 90% RH (non-condensing)
* Expandable up to 500 sensors per controller in future release.
- ETL listed to UL 61010 and CSA 22.2 NO. 61010 for product safety
- EN 61326-1:2013 for EU Directive (2014/30/EU)
- RoHS 3 EU 2015/863, WEEE, and REACH compliant
- UKCA
- FCC