Skip to main content
Share:

Senator 100


The Senator 100 is designed to provide very high sensitivity smoke detection in a small package.
 
ClassiFire Perceptive Artificial Intelligence ensures that the detector operates at optimum sensitivity for the protected environment, without the need for complex setup. This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.
 
The detector is designed to fit into a Docking Station. All sampling pipes and cables are connected to the Docking Station as a first fix operation leaving the detector to be fitted during the final commissioning phase if required. This ensures that detectors are less likely to be damaged during the installation.
 
Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems.
  • Small low cost aspirating smoke detector for easy and discreet installation
  • High sensitivity provided by laser based forward light scatter for reliable early warning
  • Single sampling pipe up to 100m in length (still air)
  • Unique ClassiFire® Perceptive Artificial Intelligence system that dynamically adjusts the detector’s operating parameters, allowing for day to day changes in the protected environment and dust separation system contamination
  • Unwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination system
  • RS485 communications built in as standard for networking and remote communications
Electrical
  • Operating voltage: 21.6 to 26.4 VDC
  • Current consumption: 400 mA
Detection
  • Detection principle: Laser light scattering mass detection and particle evaluation
  • Particle sensitivity range: 0.003µ to 10µ
  • Measurement range (%Obs/m): 0.0015% to 25%
  • Alarm levels: 4 (Aux, Pre-alarm, Alarm and Alarm 2)
Physical
  • Physical dimensions: 300 x 220 x 85mm (W x H x D)
  • Net weight: 3.8kg
  • Colour: Cream
  • Cable entries: 2 x M20
  • Material (body): Sheet steel enclosure
Environmental
  • Operating temperature: -10 to +60oC (EN54-20)
  • Relative humidity: 0 to 90% noncondensing
  • Environment: Indoor
  • IP rating: IP40
Standards & Regulation
  • Certification: EN54-20
Sampling pipework
  • Inlets: 2
  • Length: 100m maximum run (50m in moving air)
  • Diameter: 27mm OD
  • Sampling holes: up to 20 holes
  • Exhaust: 1 (optional)
Outputs
  • Standard: 2 - Alarm (n/o) and Fault (n/c)
  • Rating: 500mA @ 30V
  • Expansion: Optional input and relay card
User Interface
  • Indicators: LED
Networking
  • SenseNET (RS-485): On-board
  • CPR approved
  • LPCB approved
  • CSIRO approved
  • Small low cost aspirating smoke detector for easy and discreet installation
  • High sensitivity provided by laser based forward light scatter for reliable early warning
  • Single sampling pipe up to 100m in length (still air)
  • Unique ClassiFire® Perceptive Artificial Intelligence system that dynamically adjusts the detector’s operating parameters, allowing for day to day changes in the protected environment and dust separation system contamination
  • Unwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination system
  • RS485 communications built in as standard for networking and remote communications
Electrical
  • Operating voltage: 21.6 to 26.4 VDC
  • Current consumption: 400 mA
Detection
  • Detection principle: Laser light scattering mass detection and particle evaluation
  • Particle sensitivity range: 0.003µ to 10µ
  • Measurement range (%Obs/m): 0.0015% to 25%
  • Alarm levels: 4 (Aux, Pre-alarm, Alarm and Alarm 2)
Physical
  • Physical dimensions: 300 x 220 x 85mm (W x H x D)
  • Net weight: 3.8kg
  • Colour: Cream
  • Cable entries: 2 x M20
  • Material (body): Sheet steel enclosure
Environmental
  • Operating temperature: -10 to +60oC (EN54-20)
  • Relative humidity: 0 to 90% noncondensing
  • Environment: Indoor
  • IP rating: IP40
Standards & Regulation
  • Certification: EN54-20
Sampling pipework
  • Inlets: 2
  • Length: 100m maximum run (50m in moving air)
  • Diameter: 27mm OD
  • Sampling holes: up to 20 holes
  • Exhaust: 1 (optional)
Outputs
  • Standard: 2 - Alarm (n/o) and Fault (n/c)
  • Rating: 500mA @ 30V
  • Expansion: Optional input and relay card
User Interface
  • Indicators: LED
Networking
  • SenseNET (RS-485): On-board
  • CPR approved
  • LPCB approved
  • CSIRO approved